- 由 虚拟的现实创建于10月 13, 2023 需要 4 分钟阅读时间
1.创建VPN网关
2.创建对端网关
3.创建VPN连接(主备)
4.配置对端设备
vyos参考配置
基本配置
set interfaces ethernet eth0 address '192.168.114.248/24'
调整主备策略
set policy route-map ADD-ASPATH rule 1 action 'permit' set policy route-map ADD-ASPATH rule 1 set as-path-prepend '65000' set policy route-map SET-LP rule 1 action 'permit' set policy route-map SET-LP rule 1 set local-preference '200' set protocols bgp 65000 address-family ipv4-unicast network 192.168.114.0/24 set protocols bgp 65000 neighbor 169.254.62.1 address-family ipv4-unicast route-map export 'ADD-ASPATH' set protocols bgp 65000 neighbor 169.254.62.1 remote-as '64512' set protocols bgp 65000 neighbor 169.254.62.1 update-source '169.254.62.2' set protocols bgp 65000 neighbor 169.254.83.1 address-family ipv4-unicast route-map import 'SET-LP' set protocols bgp 65000 neighbor 169.254.83.1 remote-as '64512' set protocols bgp 65000 neighbor 169.254.83.1 timers holdtime '30' set protocols bgp 65000 neighbor 169.254.83.1 timers keepalive '10' set protocols bgp 65000 neighbor 169.254.83.1 update-source '169.254.83.2' set protocols bgp 65000 parameters router-id '169.254.83.2' set protocols static route 0.0.0.0/0 next-hop 192.168.114.1
vti方式建立ipsec配置:
set interfaces vti vti1 address '169.254.83.2/30' set interfaces vti vti2 address '169.254.62.2/30' set vpn ipsec esp-group ESP-1E compression 'disable' set vpn ipsec esp-group ESP-1E lifetime '3600' set vpn ipsec esp-group ESP-1E mode 'tunnel' set vpn ipsec esp-group ESP-1E pfs 'dh-group2' set vpn ipsec esp-group ESP-1E proposal 1 encryption '3des' set vpn ipsec esp-group ESP-1E proposal 1 hash 'sha1' set vpn ipsec ike-group IKE-1E dead-peer-detection action 'restart' set vpn ipsec ike-group IKE-1E dead-peer-detection interval '30' set vpn ipsec ike-group IKE-1E dead-peer-detection timeout '120' set vpn ipsec ike-group IKE-1E ikev2-reauth 'no' set vpn ipsec ike-group IKE-1E key-exchange 'ikev1' set vpn ipsec ike-group IKE-1E lifetime '28800' set vpn ipsec ike-group IKE-1E proposal 1 dh-group '2' set vpn ipsec ike-group IKE-1E proposal 1 encryption '3des' set vpn ipsec ike-group IKE-1E proposal 1 hash 'sha1' set vpn ipsec site-to-site peer 124.71.60.54 authentication id '58.255.36.219' set vpn ipsec site-to-site peer 124.71.60.54 authentication mode 'pre-shared-secret' set vpn ipsec site-to-site peer 124.71.60.54 authentication pre-shared-secret 'www.myj123.com' set vpn ipsec site-to-site peer 124.71.60.54 authentication remote-id '10.243.129.4' set vpn ipsec site-to-site peer 124.71.60.54 connection-type 'initiate' set vpn ipsec site-to-site peer 124.71.60.54 default-esp-group 'ESP-1E' set vpn ipsec site-to-site peer 124.71.60.54 ike-group 'IKE-1E' set vpn ipsec site-to-site peer 124.71.60.54 ikev2-reauth 'inherit' set vpn ipsec site-to-site peer 124.71.60.54 local-address '192.168.114.248' set vpn ipsec site-to-site peer 124.71.60.54 vti bind 'vti2' set vpn ipsec site-to-site peer 124.71.60.54 vti esp-group 'ESP-1E' set vpn ipsec site-to-site peer 124.71.63.186 authentication id '58.255.36.219' set vpn ipsec site-to-site peer 124.71.63.186 authentication mode 'pre-shared-secret' set vpn ipsec site-to-site peer 124.71.63.186 authentication pre-shared-secret 'www.myj123.com' set vpn ipsec site-to-site peer 124.71.63.186 authentication remote-id '10.243.129.2' set vpn ipsec site-to-site peer 124.71.63.186 connection-type 'initiate' set vpn ipsec site-to-site peer 124.71.63.186 default-esp-group 'ESP-1E' set vpn ipsec site-to-site peer 124.71.63.186 ike-group 'IKE-1E' set vpn ipsec site-to-site peer 124.71.63.186 ikev2-reauth 'inherit' set vpn ipsec site-to-site peer 124.71.63.186 local-address '192.168.114.248' set vpn ipsec site-to-site peer 124.71.63.186 vti bind 'vti1' set vpn ipsec site-to-site peer 124.71.63.186 vti esp-group 'ESP-1E'
设备配置参考
华为设备参考:
https://support.huawei.com/enterprise/zh/doc/EDOC1000097307?section=j041
Fortigate配置参考
经典VPN
https://support.huaweicloud.com/admin-vpn/zh-cn_topic_0175452091.html
5.在其他VPC和运维VPC之间建立对等连接并添加回程路由
进入其他VPC添加回程路由
场景四需要用到企业路由器ER
创建企业路由器不收费,按照连接和流量收费。
1.创建企业路由器
2.创建VPN网关
3.创建对端网关(略)
4.创建VPN连接(略)
5.进入企业路由器ER关联VPC
6.添加路由
将整个region的网段10.243.0.0/16指向运维VPC
7.在其他VPC和运维VPC之间建立对等连接并添加回程路由
进入其他VPC添加回程路由
- 无标签
0 评论